Operator's Manual for Crane, Truck Mounted, Hydraulic, 25 Ton (CCE), Grove Model TM S-300-5, Contract No. DSA 700-77-C-8511, NSN 3810-01-054-9779

Front Cover
Headquarters, Department of the Army, 1990 - Truck-mounted cranes
0 Reviews
 

What people are saying - Write a review

We haven't found any reviews in the usual places.

Common terms and phrases

Popular passages

Page 76 - The manufacturer shall include in the owner's manual the following information: (1) The statement: TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than . for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any new...
Page 73 - Federal agencies with respect to the impact of their operations on the environment, and it is specifically charged with publishing its determinations when those hold that a proposal is unsatisfactory from the standpoint of public health or welfare or environmental quality.
Page 76 - ... by any person, other than for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any product in compliance with...
Page 8 - The crane shall be standing on track which is level within 1 percent grade. (c) Radius of the load is the horizontal distance from a projection of the axis of rotation to the rail support surface, before loading, to the center of vertical hoist line or tackle with load applied.
Page 73 - The Environmental Protection Agency was established in the executive branch as an independent agency pursuant to Reorganization Plan No. 3 of 1 970 (5 USC app.), effective December 2, 1970. The Environmental Protection Agency was created to permit coordinated and effective governmental action on behalf of the environment.
Page 75 - ... shall include, in the owner's manual or in other information supplied to the ultimate purchaser, the following statement: NOISE EMISSIONS WARRANTY The manufacturer warrants to the ultimate purchaser and each subsequent purchaser that this air compressor was designed, built, and equipped to conform at the time of sale to the first retail purchaser, with all applicable USEPA noise control regulations. This warranty is not limited to any particular part, component, or system of the air compressor....
Page 38 - Lube point locations are general, as changes in manufacturer and vendor component design may result in relocation and/or number of lube fittings, fill plugs, drain plugs, etc. Specific "brand name" lubricants are not referenced since most all nationally known oil suppliers' products are suitable for use, providing they meet the requirements of the Mil Specs - and Standards appearing in this section. Should any conflict of information arise between lubricant recommendations for vendor components and...
Page 76 - ... of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use; or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. (2) The statement: Among those acts presumed to constitute tampering are the acts listed below. Immediately following this statement, the manufacturer shall include the list developed under paragraph (a) of this section....
Page 58 - ... care and with the assistance of a reputable supplier. Attention should be given to two important oil factors: 1. Antiwear additives. The hydraulic oil selected must contain the necessary additives to ensure high antiwear characteristics and excellent chemical stability. 2. Viscosity. The hydraulic oil selected must have proper viscosity to maintain a lubricating film at the operating temperature of the system. For optimum performance, suitable types of oil are: 1. Crankcase oil. If it meets the...
Page 4 - Capacities are in pounds and do not exceed 75% of tipping loads as determined by test in accordance with SAE J765. 2. Capacities are applicable to machines equipped with 20,5x25 (24 ply) tires at 75 psi cold inflation pressure, and 16.00x25 (28 ply) tires at 100 psi cold inflation pressure. 3. Defined Arc - Over front includes 6" on either side of longitudinal centerline of machine (ref, drawing C6-829-003529).

Bibliographic information