Farm Woodwork |
From inside the book
Results 1-5 of 16
Page 10
... Steel rafter framing square 1 - Pair pliers 1-10 " flat file 1 - Auger bit file 11⁄2 " 1-2 - lb . 2 - oz . Bench hatchet 1-2 - ft . , four - fold boxwood rule 1 - Cross cut saw tool 1 - Pinch bar 1 - Spoke shave 1 - Screwdriver bit 1 ...
... Steel rafter framing square 1 - Pair pliers 1-10 " flat file 1 - Auger bit file 11⁄2 " 1-2 - lb . 2 - oz . Bench hatchet 1-2 - ft . , four - fold boxwood rule 1 - Cross cut saw tool 1 - Pinch bar 1 - Spoke shave 1 - Screwdriver bit 1 ...
Page 11
... square shank 1 -File , mill cut , 6 inch . 1 -File , mill cut , 10 inch ... 6 -Files , slim taper , triangular , 6 ... steel bar carpenter's clamps ... 1 - Oilstone , coarse and fine face carborundum . 1 -Oilstone , round edge slip ...
... square shank 1 -File , mill cut , 6 inch . 1 -File , mill cut , 10 inch ... 6 -Files , slim taper , triangular , 6 ... steel bar carpenter's clamps ... 1 - Oilstone , coarse and fine face carborundum . 1 -Oilstone , round edge slip ...
Page 12
... steel 18 inch x 24 inch , polished , ( rafter framing ) 1 * -Squares , try , 8 - inch blades , wood handle .. 1 - Square , mitre ( blade fixed at angle of 45 ° ) .. Tape in case - 100 ft ..... 1 - inch iron bench screw for home made ...
... steel 18 inch x 24 inch , polished , ( rafter framing ) 1 * -Squares , try , 8 - inch blades , wood handle .. 1 - Square , mitre ( blade fixed at angle of 45 ° ) .. Tape in case - 100 ft ..... 1 - inch iron bench screw for home made ...
Page 13
... Steel square 8 inch x 12 inch . 1 -Set , stock , dies and taps inch , 26 threads , 1/4 inch , 20 , 5/16 inch , 18 , 7/16 inch , 1/2 inch , 14 for threading bolts and nuts . Desirable Equipment 1 -Drill , 5 % inch , 1⁄2 inch shank ...
... Steel square 8 inch x 12 inch . 1 -Set , stock , dies and taps inch , 26 threads , 1/4 inch , 20 , 5/16 inch , 18 , 7/16 inch , 1/2 inch , 14 for threading bolts and nuts . Desirable Equipment 1 -Drill , 5 % inch , 1⁄2 inch shank ...
Page 26
... Square Bracket 34 Chamfer holes squared at top for bits . Saw kerfs To be hung on screw hooks : To be hung on nails ~ facing all along front T bevels Braces Mallets , with screw eye in end Dividers Coping saws Drawing knife Steel square ...
... Square Bracket 34 Chamfer holes squared at top for bits . Saw kerfs To be hung on screw hooks : To be hung on nails ~ facing all along front T bevels Braces Mallets , with screw eye in end Dividers Coping saws Drawing knife Steel square ...
Other editions - View all
Common terms and phrases
12 flat 6d common nails 8d common 8d finishing nails 9 flat head angle apron back standard bench screw Berry Stand bevel Bill of Material blade bottom end bright wood screws carriage bolts centerline chisel cleats countersink cross braces cross cut saw cutting teeth detail drawing end gate end pieces farm shop fastening braces flat head bright flat head screws flat head wood floor front end handle Hardware hardwood head bright wood head wood screws hinges holes thru horizontal braces inch inside iron joint Legs Braces length lengthwise lever lower end lumber machine bolts main standards maple mortise plane planks rakers Reduce all pieces remove the stock rip saws Roof saw kerf scratch awl shellac side sills slats soft wood staples steel square Stock Bill Dimensions stock to line strap tooth trough try square vise wagon box rivets washers wood file wood screws 1½
Popular passages
Page 134 - To use the formula for any piece of lumber, multiply the thickness (in inches) by the width (in inches) by the length (in feet) and divide the resulting number by 12. Nominal dimensions must be used for the length and width. Example: How many board feet are in a 10' length of 1 X6
Page 134 - Feet.—The obvious method for finding the number of board feet in a piece of lumber is to divide the number of cubic inches by 144, or 12 X 12.
Page 11 - Carpenter's hammer, equal number, bell face, adze eye, curved claw; and plain face, straight claw 1 Drawing knife, 8" 1 Level and plumb, wood 26" 1 Level and sights 1 Mallet (or more if shop made) 3 Nail set (assorted) 1 Oiler 1 12...
Page 121 - It specifies that the length of stave shall be 28VL- inches, diameter of head 17% inches, distance between heads 26 inches and circumference of the bulge 64 inches outside measure. All barrels not coming up to this standard shall be so marked.
Page 31 - ... pocket is intended for small tools or nails and should be placed so low that when the body is bent at the waist line the contents of the pocket will not fall out. The lower pocket is intended for the rule and should be placed within easy reach of the hand. For stitching the apron no. 40 thread should be used, and the sewing machine should be set so as to make ten or twelve stitches to the inch. Material. — Denim or ticking, is the material most commonly used. For an apron thirty inches long,...
Page 5 - Company have been constructed, as a rule, in a similar way to that which has been described; but there has been a decided improvement in the character of the work...
Page 12 - ... metal handle 1 Saw, hack, 10*, with one doz. blades 1 Saw set 1 Saw vise (shop made) 3 Screw drivers, 4', 8', and 10...
Page 11 - Inch. 1 saw, hack, 10 inch, with one dozen blades. 1 saw. coping, metal handle, with one dozen blades. 1 saw, set. 1 saw, vise (homemade). 1 each, screw drivers, 4 inch, 8 Inch, and 10 inch.