## Machine Design ...American school of correspondence at Armour institute of technology, 1905 - Machine design |

### What people are saying - Write a review

We haven't found any reviews in the usual places.

### Other editions - View all

### Common terms and phrases

addendum adjustment amount of power angle babbitt metal bearing belt gearing bolts brass breadth breaking strength calculated called the pitch cast iron catch chain circular pitch circumference cogs conical surfaces cotton cycloid dedendum diam diametral pitch dimensions direction discs distance elliptical epicycloid equal face feet flange foundation plate friction gearing gear teeth gear wheel grooves guide pulley hanger holes horse-power transmitted inches in diameter journal lacing leather belts length load lubricated manilla rope nave number of arms number of teeth ordinary pawl pins pipe pitch circle pitch line pitch surfaces plane plumb line suspended power transmitted quarter-turn belt radius ratchet wheel revolutions per minute rope gearing screw seats shaft shipper shown in Fig shrouded side spur gear spur wheel square inch tallow threads toothed gears usually velocity ratio wear whole numbers width of rim wire rope worm gear worm wheel

### Popular passages

Page 25 - The CYCLOID is the curve described by a point on the circumference of a circle rolling in a straight line.

Page 23 - The radius of the pitch circle of a circular wheel is called the geometrical radius; that of a circle touching the crests of the teeth is called the real radius; and the difference between those radii, the addendum. 143. Pitch and Number of Teeth.— The distance, measured along the pitch line, from the face of one tooth to the face of the next, is called the PITCH. The pitch, and the number of teeth in circular wheels, are regulated by the following principles : — I. In wheels which rotate continuously...

Page 47 - A 6-inch belt should hare seven holes, four in the row nearest the end, and a 10-inch belt, nine holes. For any style of lacing care should always be taken that the lacing on the side of the belt next the pulleys is parallel with the edge of the belt. Joints of heavy belts which transmit large...

Page 26 - ... recorder, depending upon the required recording speed. With this experimental setup the transient behavior of the surface conductance has been studied. The transient can best be observed if the Fermi level at equilibrium is in close proximity to the surface state under investigation. As a general rule, it has been found from experience that it is most convenient to have the Fermi level above the surface state if the state is above midgap, and below the surface state for a state below midgap....

Page 50 - The belt can travel in either direction. When a crossed belt connects two pulleys, as in Fig. 48, it is necessary to give a half twist to the two straight parts of the belt in order that they may pass each other and also to bring the same side of the belt in contact with each pulley.

Page 50 - ... increasing the arc of contact. Fig. 46 and Fig. 47 show other methods of connecting shafts which are at right angles, two guide pulleys being used in each case. The same side of the belt comes in contact with each pulley, except at D (Fig. 47) where it is not possible on account of the crossed belt.

Page 26 - ... side of the inscribed equilateral triangle is to the radius of the circle as the square root of 3 is to 1 (Prop. V. Cor. 3, Bk. VI.) ; consequently, the side is to the diameter, or twice the radius, as half the square root of 3 is to 1, and half the square root of 3 is 0.8660, approximately. Also, since the ratio of the circumference of a circle to its diameter is as 3.1416 to 1, the side of the inscribed equilateral triangle, when the circumference is 1, equals 0.8660 -4- 3.1416, or 0.2757.

Page 25 - If a circle rolls on a straight line the curve traced by a point on the circumference is called a cycloid.

Page 61 - It has a polygonal prism, mn o, etc., for its pitch surface, and as the links are of the same length, the pitch line is a regular polygon, each side Iteing equal to the distance from center to center of the rivets.