Intermediate (field) (direct and General Support) and Depot Level Maintenance Manual: Generator Set, Diesel Engine Driven, Tactical Skid Mtd. 30 Kw, 3 Phase, 4 Wire, 120/208 and 240/416 Volts : DoD Model MEP-005A ... 6115-463-9094Departments of the Army, Air Force, and Navy (Including U.S. Marine Corps), 1991 - Diesel motor |
From inside the book
Results 1-5 of 25
Page xiv
... Bore and stroke . Number of cylinders Piston displacement ( cu . in . ) Dry weight ( approx . ) . Lubricating oil capacity ( with filters ) . . . . Low idle recommendations . Fuel consumption ( gals / hr ) : . • 1500 rpm ( 50 Hz , 25 kw ) ...
... Bore and stroke . Number of cylinders Piston displacement ( cu . in . ) Dry weight ( approx . ) . Lubricating oil capacity ( with filters ) . . . . Low idle recommendations . Fuel consumption ( gals / hr ) : . • 1500 rpm ( 50 Hz , 25 kw ) ...
Page 1-2
... Bore and stroke .. Number of cylinders Piston displacement ( cu . in . ) Dry weight ( approx . ) . Lubricating oil capacity ( with filters ) . . . . Low idle recommendations . Fuel consumption ( gals / hr ) : 1500 rpm ( 50 Hz , 25 kw ) ...
... Bore and stroke .. Number of cylinders Piston displacement ( cu . in . ) Dry weight ( approx . ) . Lubricating oil capacity ( with filters ) . . . . Low idle recommendations . Fuel consumption ( gals / hr ) : 1500 rpm ( 50 Hz , 25 kw ) ...
Page 1-5
... bore Skew at gap .... 1 and 12 12 groups of 2 6 groups of 5 # 16 Rd . 11.0 inches 0.64 inches ... 54 12 Type M , Grade CL155 , MIL - V - 173 . Insulating materials : Slot insulators Phase insulators Varnish TO 35C2-3-446-2 NAVFAC P - 8 ...
... bore Skew at gap .... 1 and 12 12 groups of 2 6 groups of 5 # 16 Rd . 11.0 inches 0.64 inches ... 54 12 Type M , Grade CL155 , MIL - V - 173 . Insulating materials : Slot insulators Phase insulators Varnish TO 35C2-3-446-2 NAVFAC P - 8 ...
Page 1-6
... bore 1 and 3 24 groups of 1 ( 1 group repeated 24 times ) # 18 Rd . 7.5 inches Wire size Gap bore Skew at gap ... Insulating materials : Slot insulators # 16 Rd . 13.5 inches 0.40 inches ...... 108 12 .... Phase insulators Varnish ...
... bore 1 and 3 24 groups of 1 ( 1 group repeated 24 times ) # 18 Rd . 7.5 inches Wire size Gap bore Skew at gap ... Insulating materials : Slot insulators # 16 Rd . 13.5 inches 0.40 inches ...... 108 12 .... Phase insulators Varnish ...
Page 1-8
... bore dia . 3.7490 3.7510 Cylinder bore out of round 0.0005 Cylinder bore taper 0.0005 0.0050 0.0030 0.0020 Main brg . bore less brgs . 3.0665 3.0670 Camshaft brg . bore · less brgs . 2.1870 2.1880 Oil pump bore 2.0000 2.0005 Valve tappet ...
... bore dia . 3.7490 3.7510 Cylinder bore out of round 0.0005 Cylinder bore taper 0.0005 0.0050 0.0030 0.0020 Main brg . bore less brgs . 3.0665 3.0670 Camshaft brg . bore · less brgs . 2.1870 2.1880 Oil pump bore 2.0000 2.0005 Valve tappet ...
Other editions - View all
Common terms and phrases
adjust ammeter armature Assembly Wiring Harness BLACK brush camshaft Capacitor captive washer assy Check clearance coil components connecting rod CONNECTOR coolant corrosion cracks crankshaft damage defective diameter diode Disassembly Disconnect drawing dry cleaning solvent electrical Electrical connector engine Exploded View figure Flat washer flywheel flywheel housing frequency frequency meter ft-lb fuel injection pump gasket gear governor control unit hydraulic head inch indicator Inspect INSULATION lever Lockwasher main bearing Main Load Contactor meter NAVFAC NOTE Number O-ring ohmmeter Operator and Organizational Organizational Maintenance Manual output piston plate plug position pressure pump assembly Refer removal and installation Remove nuts Remove screws Repair or replace Resistor retaining ring rheostat rotation rotor SCHEMATIC DIAGRAM seal shaft SOLDER solenoid Spacer Special Relay Assembly speed switch spring starter assembly Static Exciter stator STUD test circuit threads throttle torque transfer pump valve voltage regulator voltmeter volts watt
Popular passages
Page 7-1 - ... to the load voltage and frequency must be made to maintain corrected rated load at rated voltage and frequency. Adjustments to the voltage and frequency shall be limited to those adjustments available to the operator, specifically adjustments to the voltage or frequency adjust devices. On sets with a droop type speed control system as the prime speed control, the speed and droop portions of the control may be adjusted. Adjustments to load, voltage, or frequency controls shall be recorded on the...
Page 7-1 - ... and rated frequency. During this period, operate the recording frequency meter at a chart speed of not less than 6 in/h and record all instrument readings including thermal instrumentation at maximum intervals of 10 min. Adjustments to the load voltage and frequency must be made to maintain corrected rated load at rated voltage and frequency. Adjustments to the voltage and frequency shall be limited to those adjustments available to the operator, specifically adjustments to the voltage or frequency...
Page 7-1 - J 1 349 contain instructions for instrumentation and calculations for the ambient condition correction factor (Ref. paragraph 6.2). The engine manufacturer will specify which of the documents should be referred to for each specific engine. 6. Governor Performance Test 6.1 Stabilization — Start and operate the generator set and allow the set to stabilize at rated load, rated voltage, and rated frequency. During this period, operate the recording frequency meter at a chart speed of not less than...